Siemens SIWAREX FTC Скачать руководство пользователя страница 87

Страница: 87 / 149

EIGHING

UNCTIONS AND

ARAMETERS

Bit No.

Name

Range of Values / Meaning

Reference

23 Reserved

Reserved

24 Reserved

Reserved

Empty message

Scale in empty range

Calibration data protection

The switch for protecting the calibration data is switched on

27 Reserved

Reserved

28 Reserved

Reserved

29 Reserved

Reserved

30 Standalone

operation

activated

1, if standalone operation has been activated

Operating error

At least one operating error (fault) exists

Table 5-14

DR 30 - NAWI status bits

5.15.2 DR 30 - Conti-Status Flags

Bit No.

Name

Range of Values / Meaning

Reference

Belt control status

0: Belt control OFF
1: Belt control ON

1 Totalizing

status

1: Recording and totalizing of the dosing quantity is active
0: Dosing quantity will not be recorded

Min. belt loading exceeded

Belt loading min has been exceeded (is returned with a
delay in cases)

Belt loading max. exceeded

Belt max has been exceeded (is indicated with a delay in
cases)

Min. belt speed exceeded

Min. belt speed exceeded (returned with a delay in cases)

Max. belt speed exceeded

Max. belt speed exceeded (is indicated with a delay in
cases)

Min. pulse undercut

1 = Pulse encoder generates less than 2 pulses / second
0 = Pulse encoder generates a minimum of 2 pulses /
second

Min. belt load exceeded for
totalizing

1= Min. belt load exceeded for totalizing, the totalizing can
be performed

Scale in dynamic zero
setting range

=1, if the scale is in the dynamic zero setting range

Dynamic adjustment or zero
setting procedure is running

=1, if dynamic adjustment or zero setting procedure is
running

Dyn. zero setting aborted

1: If dynamic zero setting could not be completed or was
ended early because of leaving the zero setting range

Volumetric operation

Volumetric operation in automatic mode.

Filling Filling

activated.

> max. flow rate +/-

Change speed of flow rate too great

> min. flow rate

Minimum flow rate achieved

> max. flow rate

Maximum flow rate exceeded (in relation to the nominal
flow rate or setpoint)

Pulse 1 external

Pulses f. external summator 1

Pulse 2 external

Pulses f. External summator 2

Gravimetric operation

Gravimetric mode in automatic operation.

Emptying activated

The command for emptying was activated. Scale will not
refill, the container will empty until the limit value "Empty
range" from DR 4.

Max. control difference

Maximum control difference exists.

Reserved Reserved

Max. filling time

The maximum filling time has been achieved.

Max. time max. control
difference

The maximum control difference is at the max. defined
monitoring time.

Max. vol. time

The volumetric mode is active longer than the defined
max. monitoring time.

25 Reserved

Reserved

SIWAREX FTC

5-75

Содержание SIWAREX FTC






















































































































































Результаты поиска

Содержание SIWAREX FTC

Отзывы:

Бренды по названию

Популярные бренды

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Результаты поиска

Содержание SIWAREX FTC

Отзывы:

Бренды по названию

Популярные бренды