manualshive.com logo in svg

Siemens SIWAREX FTC, Руководство по эксплуатации устройства

Поделиться
Скачать
Siemens SIWAREX FTC Скачать руководство пользователя страница 101

C

OMMANDS

 

Note 

If the module is in operating status „Hardware fault“ or operating fault, then only the 
instructions (8) LOAD DEFAULT VALUES, (1) SERVICE_ON, (2) SERVICE_OFF 
and (9) ACK_ERROR, (150, 156) DOSING (FILLING) STOP are accepted, all 
other instructions are rejected with a data-/operating error  

 

6.2  Command List 

 

Code  Command explanation 

Comment 

 

Service and adjustment commands 

 

1 

Switch on service operation 

The SIWAREX must be switched to service 
operation to perform the adjustment. A non-adjusted 
scale cannot get out of service operation. 
 

No totalizing 

2 

Switch off service operation 

After the adjustment, service operation can be 
switched off. Only then can the scale accept 
weighing commands. 
 

Service operation 

3 

Adjustment command zero point valid 

The beginning of the characteristic curve - zero point 
of the scale - is defined with the momentary dead-
load. 
 

Service operation 

4 

Adjustment command Adjustment weight 1 valid 

The first adjustment weight is assigned with the 
momentary weight. 
  

Service operation 

5 

Adjustment command Adjustment weight 2 valid 

The second adjustment weight is assigned with the 
momentary weight. 
  

Service operation 

6 

Adjustment instruction Adjustment weight 3 
valid 

The third adjustment weight is assigned with the 
momentary weight. 
  

Service operation 

7 

Adjustment instruction Adjustment weight 4 
valid 

 The fourth adjustment weight is assigned with the 
momentary weight. 
 

Service operation 

8 

Predefine all data records with default values 

All parameters are set to the status that was 
assigned originally by the manufacturer. 

Service operation 

SIWAREX FTC 

6-89 

Содержание SIWAREX FTC






















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды