manualshive.com logo in svg

Siemens SITRANS WW100, Руководство по эксплуатации

Поделиться
Скачать
Siemens SITRANS WW100 Скачать руководство пользователя страница 32

7.8

Quick startup overview

1. Verify that the weighfeeder is installed properly as described in Installing (Page 11). Verify 

that the belt is tracking and the shear gate (if used) is properly set.

2. Verify that the weighfeeder, integrator/controller, and variable speed drive (AC or DC, if 

present) are all properly wired.

3. Refer to the supplied integrator/controller information for calibration and configuration 

information. 

7.9

Load cell replacement

WARNING

ALWAYS STOP the belt, lock-out, and/or place a "Do Not Energize" tag on the main 

disconnect before working on or around the weighfeeder.

If a load cell on the weighfeeder has been damaged and is not functioning, or if you are 

changing the capacity, you will need to replace one or all load cells.

Note
Please read and understand all of the instructions before proceeding with the replacement. 

Contact your Siemens representative for assistance if you have any questions or problems.

7.9.1

Removing old load cell

1. Confirm the new replacement load cell is correct and functional. Using a digital volt meter or 

ohm meter, verify that the resistance of the new load cell matches the resistance printed on 

the specification sheet that comes with the load cell. If the resistances do not match, the load 

cell may be damaged. Consult your Siemens representative.

2. Disconnect the load cell being replaced from the junction box. Verify that the load cell is 

connected according to the interwiring diagram supplied with this manual. Disconnect the 

load cell from the load cell junction box. Free the load cell cable from the weighfeeder so it 

is hanging free from the load cell.

3. Install the shipping bolt (tagged) through the bottom load cell mount and into the load cell. 

Tighten the shipping bolt until the load cell bottoms out on the overload bolt.

4. Remove the belt.
5. Remove the top load cell mounting bolts.  For nickel plated cells remove the threaded 

bushing from the load cell for the replacement.

6. Remove the weigh deck.

Commissioning
7.9 Load cell replacement

SITRANS WW100

32

Operating Instructions, 06/2018, A5E33560618-AC

Содержание SITRANS WW100















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды