Siemens sitrans tr300 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 96

background image

SITRANS TR200/TR300
Operating Instructions, 06/2010, A5E01071992-03

29

Operation

6

6.1

Operating and parameterizing the SITRANS TR200/TR300

Operation and parameterization

The SITRANS TR200 and SITRANS TR300 are operated and configured using a PC. The

PC is connected to the two-wire line using a suitable coupling module. The SITRANS TR300

can also be parameterized using a HART communicator. The signals needed for

SITRANS TR300 communications in accordance with the HART protocol are superimposed

on the output current in accordance with frequency shift keying. Frequency shift keying is

also abbreviated to FSK.
Measurement transmitter and parameter assignment data are stored in non-volatile memory.

Note
After parameter assignment of the SITRANS TR200/TR300, switch off the power supply to

the transmitter only after the LED on the device flashes red or lights up green and remains

lit.

6.2

Operating the with SITRANS TR200 PC/laptop and modem

NOTICE

Parameters may only be assigned to the SITRANS TR200 in the "offline" state using the

parameter assignment modem and the SIPROM T operating software. Any 4 to 20mA

current loop connected to the transmitter needs to be disconnected before parameters are

assigned.

Proceed as follows

●  For parameter assignment, connect the transmitter to the PC via the modem.
●  Use the SIPROM T parameterization software to configure the transmitter.
The power required by the transmitter is provided via:
●  the USB interface of the PC if using a USB modem
●  an external plug-in power supply if using an RS232 modem

«
...
28
29
30
31
32
...
»

Содержание sitrans tr300

































































































Отзывы:

Нет отзывов

Похожие инструкции для sitrans tr300

Бренд: Icom Страницы: 2

Бренд: Icom Страницы: 36

Бренд: Icom Страницы: 60

Бренд: Icom Страницы: 2

Бренд: Icom Страницы: 38

Бренд: Icom Страницы: 48

Бренд: Icom Страницы: 60

Бренд: Icom Страницы: 96

Бренд: Icom Страницы: 4

D-STAR ID-4100A

Бренд: Icom Страницы: 46

D-STAR ID-4100A

Бренд: Icom Страницы: 36

D-STAR ID-31A; D-STAR ID-31E

Бренд: Icom Страницы: 41

Бренд: Icom Страницы: 12

Бренд: Icom Страницы: 5

Бренд: Icom Страницы: 36

Fusion2 mini RITE

Бренд: Bernafon Страницы: 2

Multi-code 4140

Бренд: Linear Страницы: 2

Бренд: YOKOGAWA Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды