Siemens SITRANS T4200 Скачать руководство пользователя страница 51

Страница: 51 / 100

Functions

9.12 Alarm current

SITRANS TH200/TH300

Operating Instructions, 06/2010, A5E00393069-03

9.12

Alarm current

This function is used to set the magnitude of the alarm current. The alarm current signals a

sensor fault or a hardware/firmware fault.
The intensity of the alarm current can be freely selected within the preset limits of the current

control range of 3.6 mA to 23 mA. The upper and lower limit of the linear control range can

also be freely selected within the preset limits of the current control range of 3.6 mA to 23

mA.
One example of this is shown in the following diagram. The specified accuracy values of the

output signal only apply to the corresponding nominal ranges.

0HDVXULQJUDQJH

>P$@

7>@

①

Linear control range

②

Lower limit of the control range (default value = 3.80 mA)

③

Upper limit of the control range (default value = 20.5 mA)

④

Lower fault current value (default value = 3.6 mA)

⑤

Upper fault current value (default value = 22.8 mA)

⑥

Recommended setting range for lower fault current range and lower control range limit

⑦

Recommended setting range for upper fault current range and upper control range limit

Figure 9-1

Current limits with output signal 4 to 20 mA

9.13

Sensor calibration

9.13.1

Sensor calibration (one point)

This function allows the characteristic curve of the sensor that is connected to be shifted to

intersect the zero point. This allows calibration of the start of scale value of the input sensor.

This does not affect the measuring span.

Содержание SITRANS T4200





































































































Результаты поиска

Содержание SITRANS T4200

Отзывы:

Похожие инструкции для SITRANS T4200

Бренды по названию

Популярные бренды

Siemens SITRANS T4200, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS T4200

Отзывы:

Похожие инструкции для SITRANS T4200

Бренды по названию

Популярные бренды