Siemens SITRANS T4200 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 100

background image

Functional safety

7.2 Device-specific safety instructions

SITRANS TH200/TH300

40

Operating Instructions, 06/2010, A5E00393069-03

7.2.3

Settings

CAUTION

Current sensor function / Simulation
The use of the current sensor function and the simulation in safety applications can result in

undesirable operating states.
The use of both functions is not permitted in safety applications.

Operation/configuration

While operating/configuring, ensure that the technical data of the temperature transmitter are

adhered to in their respective version.

Checking the safety function

We recommend that:
●  You check the status for warnings and alarms.
●  Check the upper and lower alarm current value.
●  Perform a 2-point calibration.
●  You check the measuring accuracy that must be in the range of ± 2% for the safety

function. You check the measuring accuracy, for example, with a sensor calibration.

Note
Configuration changes in SITRANS TH300 not protected by passwords
If there is no password protection, you may have to deal with undesirable changes in the

configuration of the device.
We recommend that you enable password protection for your device after checking the

safety function.

«
...
39
40
41
42
43
...
»

Содержание SITRANS T4200





































































































Отзывы:

Нет отзывов

Похожие инструкции для SITRANS T4200

Бренд: Magenta Research Страницы: 52

Бренд: Radio Industries Страницы: 26

Бренд: La Crosse Technology Страницы: 2

Бренд: IRiver Страницы: 2

Бренд: Icom Страницы: 40

Ipify EUP-2704R-4T-PKG

Бренд: Intercoax Страницы: 2

Advantage III Gold Series

Бренд: Ebtron Страницы: 24

Бренд: Small Wonder Labs Страницы: 26

Бренд: American Fibertek Страницы: 4

Бренд: Technisonic Industries Limited Страницы: 43

Бренд: Yaesu Страницы: 39

IC-F1100D Series

Бренд: Icom Страницы: 17

Бренд: Shinkawa Страницы: 18

DM-TX-4KZ-100-C-1G

Бренд: Crestron Страницы: 5

Бренд: Crestron Страницы: 20

Бренд: anko Страницы: 4

Бренд: RCA Страницы: 40

Бренд: TESTO Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды