Siemens SITRANS T4200 Скачать руководство пользователя страница 35

Страница: 35 / 100

Operation

6.3 Operation of the SITRANS TH300

SITRANS TH200/TH300

Operating Instructions, 06/2010, A5E00393069-03

6.3.2

Operation with HART communicator

Action buttons

This button switches the HART communicator on and off. After switch-on, the hand-held

terminal automatically establishes communication with the transmitter. The online menu

appears on the display.

This button moves the cursor up through the menu bar. The selected menu line is indicated.

This button moves the cursor down through the menu bar. The selected menu line is

indicated.

This button moves the cursor to the right through the menu bar or branches into a

subroutine. The name of the selected subroutine is displayed at the top edge of the display.

This button moves the cursor to the left through the menu bar or exits a subroutine.

Function keys

Function keys F1 to F4 are located below the digital display. The various functions of the

keys in the individual menus are displayed on the bottom edge of the display.

Alphanumeric button and shift buttons

Alphanumeric values can be entered using these buttons. The function (number or letter

button) depends on the menu in question. Letters are selected by confirming the

corresponding shift button first.
Refer to the operating instructions of the HART communicator for further information about

operation and technical data.

Содержание SITRANS T4200





































































































Результаты поиска

Содержание SITRANS T4200

Отзывы:

Siemens SITRANS T4200, Руководство по эксплуатации, Страница: 35 / 100

Результаты поиска

Содержание SITRANS T4200

Отзывы: