Siemens SITRANS T4200 Скачать руководство пользователя страница 32

Страница: 32 / 100

SITRANS TH200/TH300
Operating Instructions, 06/2010, A5E00393069-03

Operation

6.1

Operating the SITRANS TH200/TH300 and assigning parameters to

The PC is used to both assign the parameters and operate the SITRANS TH200 and

SITRANS TH300. The PC is connected to the two-wire line using a suitable modem. The

SITRANS TH300 can also be parameterized using a HART communicator. The signals

needed for SITRANS TH300 communications in accordance with the HART protocol are

superimposed on the output current in accordance with frequency shift keying. Frequency

shift keying is also abbreviated to FSK.
Measurement transmitter data and data used to assign the parameters are stored in a non-

volatile memory, the EEPROM.

Note
After the parameters have been assigned to the SITRANS TH200/TH300, do not switch the

supply voltage for the transmitter off until the device's LED flashes red or lights constantly

green.

6.2

Operation of the SITRANS TH200 with PC/laptop and modem

NOTICE

Parameters may only be assigned to the SITRANS TH200 when offline using the modem

and the SIPROM T operating software. Any 4 to 20 mA current loop connected to the

transmitter needs to be disconnected before parameters are assigned.

Procedure

To assign the parameters, connect the transmitter to a PC via the modem for

SITRANS TH100/TH200/TR200.

Configure the transmitter using the SIPROM T parameterization software.

The power required by the transmitter is provided:
● By the USB port on the PC for the USB modem
● By an external plug-in auxiliary power supply for the RS232 modem

Содержание SITRANS T4200





































































































Результаты поиска

Содержание SITRANS T4200

Отзывы:

Похожие инструкции для SITRANS T4200

Бренды по названию

Популярные бренды

Siemens SITRANS T4200, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS T4200

Отзывы:

Похожие инструкции для SITRANS T4200

Бренды по названию

Популярные бренды