Siemens SITRANS L Series Скачать руководство пользователя страница 96

Страница: 96 / 106

Service and maintenance

13.1

Dismounting steps

WARNING

Before dismounting, be aware of dangerous process conditions such as e.g. pressure

in the vessel or pipeline, high temperatures, corrosive or toxic media etc.

Take note of chapters "

Mounting

and "

Connecting to voltage supply

and carry

out

the listed steps in reverse order.

13.2

Disposal

The device is made of recyclable materials. For this reason, it should be disposed of

by a specialist recycling company. Observe the applicable national regulations.
Devices described in this manual should be recycled. They may not be disposed of in

the municipal waste disposal services according to the Directive 2012/19/EC on waste

electronic and electrical equipment (WEEE).
Devices can be returned to the supplier within the EC, or to a locally approved

disposal service for eco-friendly recycling. Observe the specific regulations valid in

your country.
Further information about devices containing batteries can be found at: (

https://

support.industry.siemens.com/cs/document/109479891/

)

Note

Special disposal required

The device includes components that require special disposal.
• Dispose of the device properly and environmentally through a local waste

disposal contractor.

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 96 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: