Siemens SITRANS L Series Скачать руководство пользователя страница 93

Страница: 93 / 106

Diagnostics and troubleshooting
12.6 Return procedure

Fault description

Cause

Rectification

Measured value remains

unchanged in the close

range during emptying

False signal greater than level echo

or level echo too small

Eliminate false signals in the close

range. Check: Antenna must

protrude out of the nozzle
Remove contamination on the

antenna
Minimize interfering installations

in the close range by changing the

polarization direction
After eliminating the false signals,

the auto false echo suppression

must be deleted. Carry out a new

auto false echo suppression

Measured value jumps

sporadically towards

100 % during emptying

Changing condensation or

contamination on the antenna

Carry out auto false echo

suppression or increase auto false

echo suppression in the close range

by editing

Various echoes from an uneven

medium surface, e.g. an extraction

funnel

Check parameter "Material Type"

and adapt, if necessary

Measured value fluctuates

around 10 … 20 %

Reflections from the medium

surface via the vessel wall

(deflection)

Optimize installation position and

transmitter orientation

12.6

Return procedure

Enclose the delivery note, the return goods delivery note and the decontamination

declaration in a clear plastic pouch and attach it firmly to the outside of the

packaging. Any devices/replacement parts which are returned without a

decontamination declaration will be cleaned at your expense before further

processing.

Required forms:

• Delivery note

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 93 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: