Siemens SITRANS L Series Скачать руководство пользователя страница 84

Страница: 84 / 106

Diagnostics and troubleshooting

12.1

Maintenance

If the device is used properly, no special maintenance is required in normal

operation.

Precaution measures against buildup

In some applications, buildup on the antenna system can influence the measuring

result. Depending on the transmitter and application, take measures to avoid heavy

soiling of the antenna system. If necessary, clean the antenna system in certain

intervals.

Cleaning

The cleaning helps that the nameplate and markings on the transmitter are visible.
Take note of the following:
• Use only cleaning agents which do not corrode the housings, nameplate and

seals

• Use only cleaning methods corresponding to the housing protection rating

12.2

Rectify faults

Reaction when malfunction occurs

The operator of the system is responsible for taking suitable measures to rectify

faults.

Causes of malfunction

The device offers maximum reliability. Nevertheless, faults can occur during

operation. These may be caused by the following, e.g.:
• Transmitter
• Process
• Voltage supply

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 84 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: