Siemens SITRANS L Series Скачать руководство пользователя страница 28

Страница: 28 / 106

Connecting

5.1

Preparing the connection

Safety instructions

Always keep in mind the following safety instructions:
• Carry out electrical connection by trained, qualified personnel authorised by the

plant operator

WARNING

Only connect or disconnect in de-energized state.

Voltage supply

The data for power supply are specified in chapter "

Technical data

Note

Power the transmitter via an energy-limited circuit (power max. 100 W) acc. to

IEC 61010-1, e.g.

• Class 2 power supply unit (acc. to UL1310)
• SELV power supply unit (safety extra-low voltage) with suitable internal or

external limitation of the output current

Keep in mind the following additional factors that influence the operating voltage:
• Lower output voltage of the power supply unit under nominal load (e.g. with a

transmitter current of 20.5 mA or 22 mA in case of fault)

• Influence of additional transmitters in the circuit (see load values in chapter

Technical data

)

Connection cable

Use cable with round cross section for transmitters with housing and cable gland. To

ensure the seal effect of the cable gland (IP protection rating), find out which cable

outer diameter the cable gland is suitable for.
Shielded, two-wire cable is recommended for connecting the device.

Note

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 28 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: