Siemens SITRANS L Series Скачать руководство пользователя страница 13

Страница: 13 / 106

Safety notes
2.5 Radar frequencies for worldwide use

authorised by the manufacturer. Arbitrary conversions or modifications are explicitly

forbidden. For safety reasons, only the accessory specified by the manufacturer must

be used.
To avoid any danger, the safety approval markings and safety tips on the device must

also be observed.
The low transmitting power of the radar transmitter is far below the internationally

approved limits. No health impairments are to be expected with intended use. The

band range of the transmission frequency can be found in chapter "

Technical data

2.5

Radar frequencies for worldwide use

Country specific settings for the radar signals are determined via the frequency. The

operating mode must be set in the operating menu via the respective adjustment

tool at the beginning of the setup (see chapter "

Setup

resp. "

Menu overview

WARNING

Operating the device without selecting the frequency for the appropriate country

group constitutes a violation of the regulations of the radio approvals of the

respective country.

Further information can be found in the document "

Regulations for radar level

measuring transmitters with radio licenses

on our homepage.

2.6

Installation and operation in the USA and Canada

This information is only valid for USA and Canada. Hence the following text is only

available in the English language.
Installations in the US shall comply with the relevant requirements of the National

Electrical Code (ANSI/NFPA 70).
Installations in Canada shall comply with the relevant requirements of the Canadian

Electrical Code
A Class 2 power supply unit has to be used for the installation in the USA and

Canada.

2.7

Security information

Siemens provides products and solutions with industrial security functions that

support the secure operation of plants, systems, machines and networks.
To protect plants, systems, machines and networks against cyber threats, it is

necessary to implement (and continuously maintain) a holistic, state-of-the-art

industrial security concept. Siemens products and solutions constitute one element

of such a concept.

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 13 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: