Siemens SITRANS L Series Скачать руководство пользователя страница 100

Страница: 100 / 106

Technical data and dimensions

15.1

Technical data

Note for approved transmitters

Device specifications:

Siemens makes every effort to ensure the accuracy of these specifications, but

reserves the right to change them at any time.

Device-specific approvals:

The device-specific approvals are always to be found on the type plates on the

device.

Materials and weights

Materials, wetted parts

Antenna, process fitting

PVDF

Process seal

FKM G type threaded connections only

Materials, non-wetted parts

Housing

Plastic PBT (Polyester)

Housing seals

Silicone SI 850 R

Cable gland

Sealing, cable gland

NBR, EPDM

Blind plug, cable gland

Inspection window for the

indication

Polycarbonate

Weight

0.7 kg (1.543 lbs)

Torques

Max. torque mounting boss

7 Nm (5.163 lbf ft)

Max. torque for NPT cable

glands and Conduit tubes

10 Nm (7.376 lbf ft)

Input variable

Measured variable

The measured variable is the distance between the antenna edge of

the transmitter and the medium surface. The antenna edge is also

the reference point for the measurement.

SITRANS LR150

Operating Instructions, 08/2020,

A5E50352155

Содержание SITRANS L Series











































































































Результаты поиска

Содержание SITRANS L Series

Отзывы:

Siemens SITRANS L Series, Руководство по эксплуатации, Страница: 100 / 106

Результаты поиска

Содержание SITRANS L Series

Отзывы: