manualshive.com logo in svg

Siemens SITRANS L LU240, Краткое руководство по эксплуатации, Страница: 18 / 60

Поделиться
Скачать
Siemens SITRANS L LU240 Скачать руководство пользователя страница 18

WARNING

Exceeded maximum permissible operating pressure
Risk of injury or poisoning.
The maximum permissible operating pressure depends on the device version, pressure limit 

and temperature rating. The device can be damaged if the operating pressure is exceeded. 

Hot, toxic and corrosive process media could be released.
Ensure that maximum permissible operating pressure of the device is not exceeded. Refer 

to the information on the nameplate and/or in Technical data (Page 49).

CAUTION

External stresses and loads
Damage to device by severe external stresses and loads (e.g. thermal expansion or pipe 

tension). Process media can be released.
● Prevent severe external stresses and loads from acting on the device.

5.1.1

Installation location requirements

NOTICE
Strong vibrations
Damage to device.
● In installations with strong vibrations, mount the transmitter in a low vibration environment.

CAUTION

Aggressive atmospheres
Damage to device through penetration of aggressive vapors.
● Ensure that the device is suitable for the application.

Installing/mounting
5.1 Basic safety notes

SITRANS Probe LU240 with mA/HART

18

Compact Operating Instructions, 10/2018, A5E42673704-AB

Содержание SITRANS L LU240





























































Отзывы:

Нет отзывов