Siemens SITRANS F Скачать руководство пользователя страница 288

Страница: 288 / 350

Maintenance and diagnostics

4.8 Simulation

FST030

286

Function Manual, 04/2017, A5E35693328-AA

Setting 3.5 mA to 25 mA
Default 4.00 mA

Related
This parameter is only available if Simulation is enabled.

Path

Maintenance and diagnostics → Simulation → Simulation inputs and outputs → Channel 1

output with HART → Simulation value

4.8.1.2

Channel 2 - output

4.8.1.2.1 Operation mode

Description
Set the output functionality you want the channel to operate.

Setting Off; Current output; Frequency output; Pulse output; Status output
Default Off

Related
The setting of this parameter affects the setting options in parameter Simulation value.

Path

Maintenance and diagnostics

→ Simulation → Simulation inputs and outputs → Channel 2

output → Operation mode

4.8.1.2.2 Simulation

Description
Enables or disables simulation of channel 2 current output.

Setting Disabled; Enabled
Default Disabled

Related
Only if this parameter is set to Enabled, then the setting of parameter Simulation value will

be relevant.

Path

Maintenance and diagnostics → Simulation → Simulation inputs and outputs → Channel 2

output → Simulation

Содержание SITRANS F































































































































































































































































































































































Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS F, Руководство по эксплуатации функций

Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды