Siemens SITRANS F Скачать руководство пользователя страница 249

Страница: 249 / 350

Maintenance and diagnostics

4.2 Diagnostic events

FST030
Function Manual, 04/2017, A5E35693328-AA

247

4.2.7.4

Process events (2)

Description
Various sensor alarms can be enabled to show in the display and on the output if they occur.

Setting Various process alarms selectable
Default -

Related
The selected events will be shown in the display when they occur. Furthermore, they will be

indicated on the output if Output (2), Input/output (3) and/or Input/output (4) is set to Status

output and Status mode is set to Alarm item.

Path

Maintenance and diagnostics

→ Diagnostic events → Enable alarms → Process events (2)

4.2.7.5

Process events (3)

Description
Various sensor alarms can be enabled to show in the display and on the output if they occur.

Setting 228 Sound velocity above alarm limit; 229 Sound velocity above warning limit; 230 Sound

velocity below warning limit; 231 Sound velocity below alarm limit; 232 Flow velocity above

alarm limit; 233 Flow velocity above warning limit; 234 Flow velocity below warning limit;

235 Flow velocity below alarm limit; 236 Pressure above alarm limit; 237 Pressure above

warning limit; 238 Pressure below warning limit; 239 Pressure below alarm limit; 244 Kin.

viscosity above alarm limit; 245 Kin. viscosity above warning limit; 246 Kin. viscosity below

warning limit; 247 Kin. viscosity

Default

Related
The selected events will be shown in the display when they occur. Furthermore, they will be

indicated on the output if Output (2), Input/output (3) and/or Input/output (4) is set to Status

output and Status mode is set to Alarm item.

Path

Maintenance and diagnostics

→ Diagnostic events → Enable alarms → Process events (3)

4.2.7.6

Process events (4)

Description
Various sensor alarms can be enabled to show in the display and on the output if they occur.

Setting Various process alarms selectable
Default -

Содержание SITRANS F































































































































































































































































































































































Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS F, Руководство по эксплуатации функций

Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды