Siemens SITRANS F Скачать руководство пользователя страница 134

Страница: 134 / 350

Setup

3.4 Inputs and outputs

FST030

132

Function Manual, 04/2017, A5E35693328-AA

Path

Setup → Inputs and outputs → Channel 3

input/output → Change operation mode

3.4.5.3

Active operation (read only)

Description
Shows application possibilities.

Setting Active operation not possible, use passive wiring; Active operation possible, hardware is

able to drive the current loop

Default -

Path

Setup → Inputs and outputs → Channel 3

input/output → Active operation

3.4.5.4

Fail-safe activation condition

Description
Defines the condition the fail-safe behaviour of the channel becomes active and determines

the channel availability.

Setting Invalid process value; Maintenance alarm or Failure (NAMUR)
Default Maintenance alarm or Failure (NAMUR)

Path

Setup → Inputs and outputs → Channel 3

input/output → Fail safe activation condition

3.4.5.5

Current output

3.4.5.5.1 Pulse value

Description
Select process value for the current output.

Содержание SITRANS F































































































































































































































































































































































Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS F, Руководство по эксплуатации функций

Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды