Siemens SITRANS F Скачать руководство пользователя страница 116

Страница: 116 / 350

Setup

3.4 Inputs and outputs

FST030

114

Function Manual, 04/2017, A5E35693328-AA

3.4.4.2

Active operation (read only)

Description
Shows application possibilities.

Setting Active operation not possible, use passive wiring; Active operation possible, hardware is

able to drive the current loop

Default

Path

Setup → Inputs and outputs → Channel 2

output → Active operation

3.4.4.3

Fail-safe activation condition

Description
Defines the condition the fail-safe behaviour of the channel becomes active and determines

the channel availability.

Setting Invalid process value; Maintenance alarm or Failure (NAMUR)
Default Maintenance alarm or Failure (NAMUR)

Path

Setup → Inputs and outputs → Channel 2

output → Fail

-safe activation condition

3.4.4.4

Current output

3.4.4.4.1 Process value

Description
Select process value for the current output.

Setting Volume flow; Mass flow; Standard volume flow (only hydrocarbon and gas applications);

Flow velocity; Sound velocity; LiquIdent (only hydrocarbon applications); Density; Kinemat-

ic viscosity; Pressure; Medium temperature; Standard density (only hydrocarbon and gas

applications); Standard kinematic viscosity (only hydrocarbon applications); API gravity

(only hydrocarbon applications); Standard API gravity (only hydrocarbon applications);

Specific gravity (only hydrocarbon applications); Standard specific gravity (only hydrocar-

bon and gas applications); Auxiliary temperature; Sensor temperature; Standardizing factor

(only hydrocarbon and gas applications)

Default Mass flow

Path

Setup → Inputs and outputs → Channel 2

output → Current output → Process value

Содержание SITRANS F































































































































































































































































































































































Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS F, Руководство по эксплуатации функций

Результаты поиска

Содержание SITRANS F

Отзывы:

Бренды по названию

Популярные бренды