Siemens SITRANS F Скачать руководство пользователя страница 114 | Manualshive

Страница: 114 / 350

Siemens SITRANS F Скачать руководство пользователя страница 114

Setup

3.4 Inputs and outputs

FST030

112

Function Manual, 04/2017, A5E35693328-AA

3.4.3.8

Fail-safe activation condition

Description
Defines the condition the fail-safe behaviour of the channel becomes active and determines

the channel availability.

Setting Invalid process value; Maintenance alarm or Failure (NAMUR)
Default Maintenance alarm or Failure (NAMUR)

Related

Path

Setup → Inputs and outputs → Channel 1

-

output with HART → Fail

-safe activation condi-

tion

3.4.3.9

Damping value

Description
Sets the Damping (filtering) to smooth out response to sudden changes in measurement.
An increase to Damping value increases response time of device, and affects digital value

and loop current. If output values are noisy, increase Damping value. For faster response

time, decrease Damping value. Find a value that meets requirements of signal stability and

response time.

Setting 0.0 s to 100.0 s
Default 0.0 s

Related

Path

Setup

→ Inputs and outputs → Channel 1

-

output with HART → Damping value

3.4.3.10

Fail-safe behaviour

Description
Defines behaviour when Fail-safe is initiated.

Setting Lower fault current; Upper fault current; Last valid value; Current value; Fail-safe value
Default Lower fault current

Related

Path

Setup → Inputs and outputs → Channel 1

-

output with HART → Fail

-safe behaviour

«
...
112
113
114
115
116
...
»

Содержание SITRANS F































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды