manualshive.com logo in svg

Siemens SITRANS F US SONOKIT, Руководство по эксплуатации, Страница: 49 / 95

Поделиться
Скачать
Siemens SITRANS F US SONOKIT Скачать руководство пользователя страница 49

 

Functions 

 

7.4 Hardware key 

SITRANS FUS080 transmitter 
Operating Instructions, 07/2012, A5E03059912-02 

47

 

7.4

 

Hardware key 

HW key 

To gain access to protected parameters of the transmitter, a hard-ware jumper (HW key) 

must be installed as shown below. The HW key place is located internally on the right top 

part of PCB behind the display as shown. 

 

Figure 7-3 

HW key behind the display (pins to the right) 

 

Note 
Important 
In this mode, with the HW key installed, many parameters in PDM are opened. If these 

parameters are changed, it can seriously affect the meter accuracy and operation. Be careful 

when writing new parameters. 

Changing the HW-protected parameters 

1.

 

Disconnect power supply to transmitter, i.e. battery plug and/or the mains power supply 

2.

 

Remove frame and display from transmitter. 

3.

 

Insert HW key as shown in figure above. 

4.

 

Remount display and frame on transmitter. 

5.

 

Restart device. 

6.

 

Make parameter changes via PDM. 

7.

 

Download parameter changes to device. 

8.

 

Remove HW key by following the steps above. 

Содержание SITRANS F US SONOKIT
































































































Отзывы:

Нет отзывов