Siemens SITRANS F TRANSMAG 2 Скачать руководство пользователя страница 85

Страница: 85 / 126

Technical specifications

Mode of operation

Mode of operation and design
Measuring principle

Electromagnetic with pulsed alternating field (PAC)

Magnetic field excitation

Automatic power supply synchronization

50 Hz AC power supply

• Bipolar 16.7 Hz
• Bipolar with prepulse 10 Hz
• Unipolar 8,33 Hz

60 Hz AC power supply

• Bipolar 20 Hz
• Bipolar with prepulse 12 Hz
• Unipolar 10 Hz

Measuring accuracy under reference conditions

Measuring tolerance of pulse output
At v > 0.25 m/s (0.82 ft/s)

≦ 0.5 % of the measured value, ± 0.0012 m/s (0.0039 ft/s)

At v < 0.25 m/s (0.82 ft/s)

≦ 0.0025 m/s (0.0082 ft/s)

Measuring tolerance of analog output 4
to 20 mA

Same as pulse output; plus ± 0.1 % conversion error ± 20 μA

Repeatability

0.2 % of the measured value

Reference conditions

Reference conditions
Medium process temperature

+25 °C ± 5 °C (77 °F ± 9 °F)

Ambient temperature

+25 °C ± 5 °C (77 °F ± 9 °F)

Warm-up time min.

30 min

Installation conditions

Inlet pipe section

≧ 10 x DN

Outlet pipe section

≧ 5 x DN; installed centered to pipe

Medium

water without gaseous and solid parts

Conductivity

> 200 μS/cm

Magnetic current frequency

bipolar with prepulse

TRANSMAG 2 with MAG 911/E
Operating Instructions, 03/2021, A5E00102775-AC

Содержание SITRANS F TRANSMAG 2































































































































Результаты поиска

Содержание SITRANS F TRANSMAG 2

Отзывы:

Siemens SITRANS F TRANSMAG 2, Руководство по эксплуатации, Страница: 85 / 126

Результаты поиска

Содержание SITRANS F TRANSMAG 2

Отзывы: