Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 164

Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 85

Troubleshooting/FAQs

9

9.1

Fault codes

Error system

MAG 8000 can detect and report 14 different faults.
The faults are divided into two types: Fatal errors and Warnings.
Fatal errors: Faults 1, 2, 3, and 4
Warnings: Faults 5, 6, 7, 8, 9, L, E, C, d, and 14

Fault
codes

Name/text

Description

Cause

Remedy

1

Insulation fault "Cross-talk" between

coil circuit and electro‐

des. An insulation fault

will result in a offset er‐

ror on flow measure‐

ment
(Advanced version on‐

ly)

● Defect cables between

sensor and transmitter

● Wrong connections of

remote cables

● Water between coils

and electrodes – could
be caused by a broken
liner

● Pollution/moisture on

PCB caused by water in
encapsulation

Check cable and wiring installation and dis‐

turbing elements in the surrounding.
Re-activation of insulation test (parameter

800) will reset alarm and start a new insu‐

lation test.
During the 4 minute insulation test, meas‐

urement is disabled.
Alarm remains active until a new test period

detects no failures.

2

Coil current

fault

Error in the coil circuit.

Coil current has not set‐

tled within specified pe‐

riod.
A short-circuit in the coil

can NOT be detected

● Coils have been

disconnected could be
caused by broken cable
or wires

Check cable and wiring installation.
Alarm remains active until the fault condi‐

tion is corrected.

3

Amplifier over‐

load

Input signal is outside

expected range.
Input amplifier circuit

can not provide a stable

measurement.
A short circuit between

the two electrodes or

between a electrode

and common can NOT

be detected

● Electrodes have been

disconnected, or
connected to ground

Check cable and wiring installation.
Alarm remains active until the fault condi‐

tion is corrected.

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

85

«
...
83
84
85
86
87
...
»

Содержание SITRANS F M MAG 8000





































































































































































Отзывы:

Нет отзывов