manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 83 / 164

Поделиться
Скачать
Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 83

Additional Support   

 If you have additional questions about the device, please contact your local Siemens 

representative and offices at:
AUTOHOTSPOT

See also

Service and support (

http://www.siemens.com/automation/service&support

)

Local contact person (

http://www.automation.siemens.com/partner

)

Technical support (

http://support.automation.siemens.com/WW/view/en/16604318

)

Support request (

http://www.siemens.com/automation/support-request

)

8.9

Return procedures

Enclose the delivery note, the cover note for return delivery and the declaration of 

decontamination form on the outside of the package in a well-fastened clear document pouch.     

Required forms

● Delivery Note
● Cover Note for Return Delivery with the following information

Cover note (

http://cache.automation.siemens.com/dnl/zY/

zY0OTg1AAAA_16604370_TxtObj/Begleitschein_RW_AD.pdf

) 

– product (ordering number)
– number of devices or spare parts returned
– reason for the return

● Declaration of Decontamination 

Declaration of Decontamination (

http://pia.khe.siemens.com/efiles/feldg/files/Service/

declaration_of_decontamination_en.pdf

) 

With this declaration you certify 

that the returned products/spare parts have been carefully 

cleaned and are free from any residues.

If the device has been operated together with toxic, caustic, flammable or water-damaging 

products, clean the device before return by rinsing or neutralizing. Ensure that all cavities 

are free from dangerous substances. Then, double-check the device to ensure the cleaning 

is completed.

We shall not service a device or spare part unless the declaration of decontamination 

confirms proper decontamination of the device or spare part. Shipments without a 

declaration of decontamination shall be cleaned professionally at your expense before 

further proceeding. 

You can find the forms on the Internet and on the CD delivered with the device.

Service and maintenance

8.9 Return procedures

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

83

Содержание SITRANS F M MAG 8000





































































































































































Отзывы:

Нет отзывов