Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 41

Страница: 41 / 164

Commissioning

The meter can be configured using a PC software package - either SIMATIC PDM or Flow

Tool.
Both SIMATIC PDM and Flow Tool are software packages for configuring, parameterizing,

commissioning and maintaining devices (e.g. transducers) and for configuring networks and

PCs.
For commissioning via Flow Tool, refer to the appendix "Flow Tool" (Page 115).

6.1

SIMATIC PDM

Among other features, SIMATIC PDM contains a simple monitoring of process values,

interrupts and status/diagnosis signals of device. This chapter describes how to set up

SIMATIC PDM and how to configure the device for commissioning.

Note
For instructions on installation and operation of SIMATIC PDM, refer to the SIMATIC PDM

Getting Started

6.2

Initial commissioning via SIMATIC PDM

This chapter describes how to install the PDM device driver (EDD). The newest EDD driver is

available on the internet (

http://support.automation.siemens.com/WW/view/en/

19701862/133100

Install the EDD files from SIMATIC PDM "Manage Device Catalog" via the following steps:
Windows START menu → program folder "SIMATIC" → SIMATIC PDM → Manage device

catalog.

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы:

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 41 / 164

Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы: