Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 13

Страница: 13 / 164

Description

3.1

System components

A SITRANS F M MAG 8000 water meter system includes:
● A transmitter and a sensor. The transmitter is either compact mounted (integral) or remote

mounted at a distance of maximum 30 m (100 ft).

● An internally or externally mounted battery supply or 115 to 230 V AC or 12/24 V AC/DC

power supply with battery backup.

Communication solutions

The following communication modules are available:
● RS 232
● RS 485 Modbus RTU
● Encoder interface for AMR solutions
● GSM/GPRS module

3.2

Operating principle

MAG 8000 is a microprocessor-based water meter with graphical display and key for optimum

customer operation and information on site. The transmitter drives the magnetic field in the

sensor, evaluates the flow signal from the sensor, and calculates the volume passing through.

It delivers the required information via the integrated pulse output or communication interfaces

as part of a system solution. Its intelligent functionality, information and diagnostics ensure

optimum meter performance and information to optimize water supply and billing.
MAG 8000 Standard and MAG 8000 CT can be ordered as a Basic or an Advanced version,

and MAG 8000 Irrigation as Basic version only.

3.3

Design

MAG 8000 is a battery-supplied magnetic inductive water meter for revenue, district and

irrigation metering application.

Figure 3-1

MAG 8000 product program

SITRANS MAG 8000

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы:

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 13 / 164

Результаты поиска

Содержание SITRANS F M MAG 8000

Отзывы: