manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Руководство по эксплуатации, Страница: 122 / 164

Поделиться
Скачать
Siemens SITRANS F M MAG 8000 Скачать руководство пользователя страница 122

Figure A-4

Customer-specified parameter list

There is no limitation on the number of customer-specified parameter lists. 
Saving the project will make the parameter list configuration available for future use.

Note
Saving the file with only the customized parameter list expanded will make future monitoring 

and changes of parameters easier.

See also

www.siemens.com/flow (

www.siemens.com/flow

)

A.5

Unit selection

MAG 8000 and MAG 8000 CT are delivered with totalizer and flow rate units as ordered via 

the MLFB structure.
The standard MAG 8000 units for each region are:
● Europe: m

3

 for totalizer and m

3

/h for flow rate

● US: Gallon for totalizer and GPM (Gallon per minute) for flow rate
● Australia: ML for totalizer and ML/d (Mega liter/day) for flow rate

Flow Tool
A.5 Unit selection

SITRANS MAG 8000

122

Operating Instructions, 11/2018, A5E03071515-AE

Содержание SITRANS F M MAG 8000





































































































































































Отзывы:

Нет отзывов