Siemens SITRANS F FUE380 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 102

Siemens SITRANS F FUE380 Скачать руководство пользователя страница 46

Battery status
There are two symbols for battery charge status:
● "Battery full" indicates battery charge above the warning level (6-year hour counter).
● "Battery low" indicates battery charge below the warning level and that the battery should

be replaced.

Note
"Battery low" only indicates that battery charge is below a pre-set level, not that charge is zero.
Flow measurement continues uninterrupted until the battery is completely drained.

Table 6-2

Battery status information symbols

Symbol

Description
Battery status, full

Battery status, low

6.2

Navigating the menu structure

Press the push button briefly (less than 2 seconds) to navigate between the following menu

items:

Table 6-3

Menu items

Menu

Parameter

Display example

Comments

Menu 1

Flow volume totalizer 1

Factory preset is forward vol‐

ume flow.
The battery symbol shows

full.

Menu 2

Flow volume totalizer 2

FUS380 - The menu 2 is acti‐

vated and shows totalizer 2

for the reverse accumulated

volume.
FUE380 - The menu 2 is de‐

activated, but with ordered Z-

option E21 the menu 2 shows

totalizer 2 for the reverse ac‐

cumulated volume.

Menu 3

Actual flow rate

Negative values indicate re‐

verse flow calculation.

Commissioning
6.2 Navigating the menu structure

FUS380/FUE380

46

Operating Instructions, 09/2016, A5E00730100-AB

«
...
44
45
46
47
48
...
»

Содержание SITRANS F FUE380







































































































Отзывы:

Нет отзывов