Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 9

Страница: 9 / 198

Communication

2.1

System integration

This chapter provides information on how to integrate the device in a point-to-point or multidrop

Modbus RTU network in non-hazardous or hazardous areas. Many details of network design

are beyond the scope of these operating instructions. The points below provide an overview

of the major design criteria. For further details contact Siemens.

2.2

System configuration

Non-hazardous areas

The following figures show examples of installations in point-to-point and multidrop

configurations in non-hazardous areas.

0DVWHU

0HDVXULQJ

GHYLFH

Figure 2-1

Point to point configuration in non-hazardous locations

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 9 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: