Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 70

Страница: 70 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

7405

Float / 4

Lower warning

limit

Falling below this limit

causes a warning.

-max. mass

flow

[kg/s]

(7400)

-max. mass flow -

+max. mass flow

Read /

write

7407

Float / 4

Lower alarm

limit

Falling below this limit

causes an alarm.

-max. mass

flow

[kg/s]

(7400)

-max. mass flow -

+max. mass flow

Read /

write

7412

Float / 4

Hysteresis

Hysteresis that affects

the alarm and warning

limits.

[kg/s]

(7400)

0 - max. mass flow

Read /

write

Table 4-18

Density settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

7601

Float / 4

Upper alarm

limit

Exceeding this limit

causes an alarm.

max. density

[kg/m

]

(7600)

0 - max. density

Read /

write

7603

Float / 4

Upper warning

limit

Exceeding this limit

causes a warning.

max. density

[kg/m

]

(7600)

0 - max. density

Read /

write

7605

Float / 4

Lower warning

limit

Falling below this limit

causes a warning.

1.0

[kg/m

]

(7600)

0 - max. density

Read /

write

7607

Float / 4

Lower alarm

limit

Falling below this limit

causes an alarm.

1.0

[kg/m

]

(7600)

0 - max. density

Read /

write

7612

Float / 4

Hysteresis

Hysteresis that affects

the alarm and warning

limits.

[kg/m

]

(7600)

0 - max. density

Read /

write

Medium temperature settings

Table 4-19

Medium temperature settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[units]

(units register)

Value range /

Setting options

Access

level

7701

Float / 4

Upper alarm

limit

Exceeding this limit

causes an alarm.

max. medium

temperature

[°C]

(7700)

min. medium temperature -

max. medium temperature

Read /

write

7703

Float / 4

Upper warning

limit

Exceeding this limit

causes a warning.

max. medium

temperature

[°C]

(7700)

min. medium temperature -

max. medium temperature

Read /

write

MODBUS commands
4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 70 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: