manualshive.com logo in svg

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 167 / 198

Поделиться
Скачать
Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 167

Channel 3

Table 4-84

Channel 3   

Modbus 

register

Data type / 

Size in bytes

Parameter

Description

Default value 

[unit]

(unit register)

Value range / 

Setting options

Access 

level

9103

Float / 4

Current output 

value

Output current value if 

configured to current 

output.

-

-

Read 

only

9128

Unsigned / 2

Error status

Error status if config‐

ured to current output.

-

● Bit 0: Overflow
● Bit 1: Underflow
● Bit 2: Fail mode 

activated

● Bit 3: Cable break
● Bit 4: Output current 

cannot be 
established (read 
back deviation > 0.1 
mA)

Read 

only

9140

Unsigned / 2

Status output

Status value if config‐

ured to status output.

-

-

Read 

only

9269

Float / 4

Pulse status 

output

Amount done if config‐

ured to pulse output.

-

-

Read 

only

9272

Unsigned / 2

Error status

Error status if config‐

ured to pulse output.

-

● Bit 0: The pulse 

output has reached 
the maximum pulse 
output frequency

● Bit 1: Fail mode is 

activated

Read 

only

9287

Unsigned / 4

Pulse counter

Pulse output since 

startup.

-

-

Read 

only

9200

Float / 4

Frequency out‐

put value

Frequency value if con‐

figured to frequency 

output.

-

-

Read 

only

9203

Unsigned / 2

Error status

Error status if config‐

ured to frequency out‐

put.

-

● Bit 0: Overflow
● Bit 1: Underflow
● Bit 2: Fail mode 

activated

Read 

only

10503

Float / 4

Current input 

value

Input current value if 

configured to current in‐

put.

-

-

Read 

only

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

167

Содержание SITRANS F Coriolis FCT030







































































































































































































Отзывы:

Нет отзывов