Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 127

Страница: 127 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

8057

Unsigned / 2

Trend log time

window

Scaling of the time axis.

Effective when Trend

scale mode (8056) is

set to 1.

● 0: 1 min
● 1: 5 min
● 2: 15 min
● 3: 30 min
● 4: 1 h
● 5: 2 h
● 6: 3 h

Read /

write

8058

Float / 4

Trend scale low‐

er limit

Scaling of the y-axis.

Lower limit. Effective

when Trend scale

mode (8056) is set to 1.

0.0

Read /

write

8060

Float / 4

Trend scale up‐

per limit

Scaling of the y-axis.

Upper limit. Effective

when Trend scale

mode (8056) is set to 1.

0.0

Read /

write

View 3 settings

Table 4-53

View 3 settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

9014

Unsigned / 2

Enable or disa‐

ble

Enable or disable view. 1

● 0: Disabled.
● 1: Enabled.

Read /

write

9009

Unsigned / 2

View

Type of appearance.

● 1: Single value.
● 2: Active diagnostic

events.

● 3: Three values.
● 4: Totalizer.
● 6: 1 value and bar

graph.

● 7: 1 value and graph.
● 8: Six values.
● 9: Six diagnostic

values.

Read /

write

9024

Unsigned / 2

value

Selection of the first val‐

ue.

See Selectable values

dependent on the view

type (Page 133).

Read /

write

9025

Unsigned / 2

value

Selection of the second

value. Depending on

the number of values.

See Selectable values

dependent on the view

type (Page 133).

Read /

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

127

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 127 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: