Siemens SITRANS F Coriolis FCT030 Скачать руководство пользователя страница 123

Страница: 123 / 198

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

6190

String / 16

Current time

Current time in ISO

8610 format
(YYYY-MM-DD

hh:mm).

Read

only

10864

String / 32

Current time

high resolution

Current time in ISO

8610 format
(YYYY-MM-DD

hh:mm).

Read

only

4.10.5.10

Local display

General settings

Table 4-50

General settings

Modbus

Data type /

Size in bytes

Parameter

Description

Default value

[unit]

(unit register)

Value range /

Setting options

Access

level

9002

Unsigned / 2

Language

Language.

● 0: English
● 1: German
● 2: French,
● 3: Italian,
● 4: Spanish
● 5: Chinese

Read /

write

9098

Unsigned / 2

Backlight

Duration of backlight

activity after last key

press.

[s]

0 - 240

Read /

write

9094

Unsigned / 2

Inactivity time‐

out

Duration of display ac‐

tivity after last key

press.

[min]

0 (always on) - 60

Read /

write

9095

Unsigned / 2

Auto logout

Defines the need to en‐

ter PIN after leaving the

menu and returning to

any top level view.

● 0: Enter menu without

PIN for 10 min.

● 1: Automatic logout.

Read /

write

9096

Unsigned / 2

Help appear‐

ance

Duration until help text

appears.

[s]

0 - 20

Read /

write

9097

Unsigned / 2

Enable local ac‐

cess control

Controls local access.

● 0: Disabled. Allows

users to modify
settings without PIN.
Expert access is
excluded.

● 1: Enabled.

Read /

write

MODBUS commands

4.10 Modbus holding registers tables

FCT030 Modbus (From firmware 4.0)

Function Manual, 06/2018, A5E39931813-AB

123

Содержание SITRANS F Coriolis FCT030







































































































































































































Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы:

Siemens SITRANS F Coriolis FCT030, Руководство по эксплуатации функций, Страница: 123 / 198

Результаты поиска

Содержание SITRANS F Coriolis FCT030

Отзывы: