Siemens SITRANS AW 7MP3112 Series Скачать руководство пользователя страница 18

Страница: 18 / 76

Legacy DCS
without
HART support

Remote I/O
station w/o HART
support

SITRANS

MDS

IWLAN
IEEE802.11

IE/WSN-PA LINK

SITRANS AW200

Industrial Ethernet

WirelessHART

Industrial Ethernet

OFIBUS

4 –20 mA

Figure 4-2

WirelessHART network with diagnostics station

The WirelessHART network is capable of organizing itself. This is the responsibility of the

"Network Manager" software that automatically organizes, establishes and manages

WirelessHART networks. The Network Manager software calculates the optimum connection

paths between the network nodes and selects an alternative path via which the data will be sent

if an error or fault occurs.
After installation, every WirelessHART adapter is capable of recognizing its neighbors. The

WirelessHART adapter detects the strength of the wireless signal, synchronizes itself, obtains

frequency information and then establishes connections to its neighbors in the wireless

network. This means that the user is not required to make any settings regarding the

organization of the network.

Power supply of the WirelessHART adapter

The power required by the WirelessHART adapter is provided by the supplied battery unit. The

field device can be supplied by the battery unit or by a separate power supply. It is possible to

connect two-wire and four-wire field devices.
If you use the battery to supply power to the field device, this shortens the life of the battery.

4.2

Siemens HART field devices for the adapter

Up to four HART and 4 … 20 mA field devices can be connected to the WirelessHART adapter

SITRANS AW200. Depending on their electrical characteristics, the field devices can either be

supplied with power by the WirelessHART adapter or you require an external power supply.

Information on Siemens HART field devices for the adapter is available under: Services &

Support (

http://www.siemens.com/automation/service&support

)

Mode of operation and system
4.2 Siemens HART field devices for the adapter

WirelessHART Adapter SITRANS AW200

Operating Instructions, 02/2020, A5E02777161-AA

Содержание SITRANS AW 7MP3112 Series













































































Результаты поиска

Содержание SITRANS AW 7MP3112 Series

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITRANS AW 7MP3112 Series, Руководство по эксплуатации

Результаты поиска

Содержание SITRANS AW 7MP3112 Series

Отзывы:

Бренды по названию

Популярные бренды