Siemens SITOP 6EP1336-3BA00 Скачать руководство пользователя страница 12

Страница: 12 / 70

Description, device design, dimension drawing

2.3 Potentiometer

SITOP modular 1ph/2ph

Manual, 04.2018, C98130-A7548-A1-4-7629

2.3

Potentiometer

The potentiometer

③

on the front of the device is used to set the output voltage. The output

voltage is set to 24 V in the factory, and can be adjusted in the range 24 - 28.8 V; for

example, to compensate voltage drops across long supply lines to the connected load.

Figure 2-5

Potentiometer (example of 6EP1337-3BA00)

NOTICE
Thermal overload possible
When adjusting the output voltage to > 24 V, the output current must be derated by 4 %/V,

or the permissible ambient temperature must be taken into account with 3 °C/V.

Note
It is only permissible to use an insulated screwdriver when actuating the potentiometer.

For notes on actuating the potentiometer (screwdriver, torque), see Figure 2-2 Terminal data

for 6EP1333-3BA10 and 6EP1334-3BA10 (Page 10), Figure 2-3 Terminal data for 6EP1336-

3BA00 (Page 11) and Figure 2-4 Terminal data for 6EP1337-3BA00 (Page 11).

Содержание SITOP 6EP1336-3BA00







































































Результаты поиска

Содержание SITOP 6EP1336-3BA00

Отзывы:

Бренды по названию

Популярные бренды

Siemens SITOP 6EP1336-3BA00, Руководство пользователя

Результаты поиска

Содержание SITOP 6EP1336-3BA00

Отзывы:

Бренды по названию

Популярные бренды