Siemens SIRIUS Series Скачать руководство пользователя страница 137

Страница: 137 / 182

Service

13.2 Installing/Removing auxiliary and control conductor terminal blocks

SIRIUS 3RA6 Compact Starter
System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

135

13.2

Installing/Removing auxiliary and control conductor terminal blocks

Installing auxiliary and control conductor terminal blocks on the compact starter

The auxiliary and control conductor terminals are mechanically coded to prevent mix-ups.

The terminals are marked as follows:

Figure 13-1 Coding of auxiliary and control conductor terminals

①

A: Top/front mounting position on compact starter

②

B: Bottom/rear mounting position on compact starter

Note
The auxiliary and control conductor terminal blocks can only be installed in the following

order because of how they are arranged:
1. Lower/rear auxiliary circuit terminal (B)
2. Top/front control circuit terminal (A)

Requirements

DANGER

Danger, high voltage!
Electrical voltage can result in electric shocks or burns.
Before starting work, disconnect the systems and devices from the power supply.

●

The compact starter must be switched off (actuator set to OFF position).

Содержание SIRIUS Series























































































































































































Результаты поиска

Содержание SIRIUS Series

Отзывы:

Siemens SIRIUS Series, Системное руководство, Страница: 137 / 182

Результаты поиска

Содержание SIRIUS Series

Отзывы: