Siemens SIRIUS 3RW44 Скачать руководство пользователя страница 147

Страница: 147 / 292

Diagnostics and messages

8.1 Diagnostics and messages

3RW44 soft starters
Manual, 03/2017, NEB535219502000/RS-AB/008

147

8.1.3

Device fault

Message

Cause/solution

Switching element defective (for

devices with product version ≥

*E04*)

At least one bypass element has welded and/or at least one thyristor has fused. This

message is generated when the control supply voltage is applied and current flow is

being measured (via the soft starter) when no start command has been issued.

Remedy: Contact your SIEMENS representative or Technical Assistance (see

chapter Important notes (Page 9)).

Contact 1 failed

Thyristor in phase L1 failed (This message is issued when the start command is

issued.)

Remedy: Contact your SIEMENS representative or Technical Assistance.

Contact 2 failed

Thyristor in phase L2 failed (This message is issued when the start command is

issued.)

Remedy: Contact your SIEMENS representative or Technical Assistance.

Contact 3 failed

Thyristor in phase L3 failed (This message is issued when the start command is

issued.)

Remedy: Contact your SIEMENS representative or Technical Assistance.

Flash memory error

The device memory is faulty.
Remedy: Contact your SIEMENS representative or Technical Assistance.

Device not named

Device not named, still has to receive naming data.
Remedy: Contact your SIEMENS representative or Technical Assistance.

Incorrect name version

The naming and firmware versions do not match.
Remedy: Contact your SIEMENS representative or Technical Assistance.

Bypass element defective

The bypass contactor is welded or defective.
Remedy: Contact your SIEMENS representative or Technical Assistance.

Heatsink temperature sensor wire

break

Option 1: The temperature sensor on the heatsink of the starter is not connected or

defective.
Option 2: 3RW4465 and 3RW4466 may have a defective fan on the front of the

starter.
Remedy: Only in the case of 3RW4465 and 3RW4466: After about 30 to 60 minutes

cooling time, try to rectify the fault by switching the control supply voltage off and

then on again. If this was successful, check whether the fan on the front of the soft

starter is running when the start command is issued. If not, it may be necessary to

replace the fan. (The fan on the front of the starter and also the fans on the bottom of

the unit both be running simultaneously in fault-free operation).

For all 3RW44 starters:

If it was not possible to reset the fault message by switching the control supply

voltage off and on again, contact your SIEMENS partner or Technical Assistance.

Heatsink sensor short-circuit

The temperature sensor on the heatsink of the starter is not connected or defective.
Remedy: Contact your SIEMENS representative or Technical Assistance.

Possible ohmic value for a defective thyristor: <2 kOhm (L-T).

Содержание SIRIUS 3RW44





































































































































































































































































































Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды

Siemens SIRIUS 3RW44, Руководство пользователя

Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды