Siemens SIRIUS 3RW44 Скачать руководство пользователя страница 135

Страница: 135 / 292

Device functions

7.5 Current limits for load monitoring

3RW44 soft starters
Manual, 03/2017, NEB535219502000/RS-AB/008

135

Typical applications for the slow speed function

This function is suitable for applications with a low counter-torque, e.g. positioning of

machine tools.

Note
In addition to the set parameters, motor-specific characteristics and the connected load

influence the speed resulting from the slow speed function and the slow speed torque

generated in the motor.

Note
For operation of the motor with the specified slow speed parameters, the "slow speed"

function must be assigned to one control input, and the "Motor CW PS1/2/3" or "Motor CCW

PS1/2/3" function must at the same time be assigned to the other. See also the circuit

suggestion in chapter Typical circuit diagrams (Page 216).
Directions of rotation:

Right (CW): Rotation in line phase direction

Left (CCW): Rotation contrary to the line phase direction

Note
Due to the reduced motor speed and the related reduced self-cooling of the motor, this mode

is not recommended for continuous operation.

CAUTION

Risk of property damage
For optimum motor protection, use the combination of electronic motor overload protection

and evaluation of a temperature sensor installed in the motor.

7.5

Current limits for load monitoring

Low and high current limits can be set so that a message can be issued if they are exceeded

or undershot.

Lower current limit

The lower current limit could be used, for example, to indicate tearing of a V belt and the

associated no-load current of the motor or if the filter of the fan is clogged.

Upper current limit

The upper current limit can be used to determine increased power loss in the application, for

example caused by bearing damage.

Содержание SIRIUS 3RW44





































































































































































































































































































Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды

Siemens SIRIUS 3RW44, Руководство пользователя

Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды