Siemens SIRIUS 3RW44 Скачать руководство пользователя страница 131

Страница: 131 / 292

Device functions

7.3 Coasting methods

3RW44 soft starters
Manual, 03/2017, NEB535219502000/RS-AB/008

131

7.3.3

DC braking/combined braking

In the case of DC braking or combined braking, coasting down or the natural run-down of the

load is shortened.
The soft starter imposes a (pulsating) direct current in phases L1 and L3 on the motor stator.

This current generates a permanent magnetic field in the stator. Since the rotor is still

rotating due to its mass inertia, currents are induced in the short-circuited rotor winding that

generate a DC braking torque.

Note
The DC braking/combined braking stopping function is not possible in inside-delta circuits.

Note
The pulsating direct current loads the system asymmetrically and the motor and the feeder

must be designed for the higher current load during the stopping procedure. It may be

necessary to overdimension the soft starter.

Note
Two braking variants are available:
Combined braking:

Use the combined braking function if applications with small mass inertias (centrifugal

masses) are to be stopped (J

load

≤

motor

). The real coast-down time can vary during braking

operations when the combined braking function is applied. Use the DC braking function if a

uniformly long braking time is to be achieved.
DC braking:

Use the DC braking function if applications with small mass inertias (centrifugal masses) are

to be stopped (J

load

≤

5 x J

motor

). An external braking contactor is required for the DC

braking function.

CAUTION

Risk of property damage.
For optimum motor protection, the combination of electronic motor overload protection and

evaluation of a temperature sensor installed in the motor is recommended.

Combined braking coasting method

When the combined braking coasting method is chosen, the dynamic braking torque, DC

braking torque and coast-down time can be set on the starter.

Dynamic braking torque

The dynamic braking torque determines the braking effect at the start of the braking process

to reduce the speed of the motor. The braking process is then continued automatically using

the DC braking function.

Содержание SIRIUS 3RW44





































































































































































































































































































Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды

Siemens SIRIUS 3RW44, Руководство пользователя

Результаты поиска

Содержание SIRIUS 3RW44

Отзывы:

Похожие инструкции для SIRIUS 3RW44

Бренды по названию

Популярные бренды