Siemens SIREMOBIL Iso-C Скачать руководство пользователя страница 50

Страница: 50 / 128

SIREMOBIL Iso-C

SPR2-230.061.01

Page 14 of 30

Siemens AG

System Manual

Rev. 13

12.04

CS PS 24

Medical Solutions

5 - 14

Adjustments / Programs

Concluding steps

•

Switch off the system and switch it back on again.

•

Return to the main menu by pressing ESC at the service PC.

•

Select the "Data, Backup..." menu.

•

Click "parameter" in the Backup window.

•

Then click "Backup" .

•

Enter "slot diaphragm adjusted" under "Remarks for Parameter".

•

Then click "OK" . The new position values are stored to disk.

•

You can now exit from the service program.

Collimator displays on the monitor

Prerequisites

•

Camera rotation, collimators for X-Iris and slot diaphragm must be set correctly

Collimator display, X-Iris

•

Connect the service PC to the serial interface of the SIREMOBIL.

•

Start the service program.

•

Select the "Adjustment, Calibrations..." menu.

•

Respond to the query with "Yes".

•

Select "Screen Display COLLIMATOR" in the "Function Groups:" combo box.

Start adjustment

•

In the "Available Functions:" window select "Init" and click on "Execute". The X-Iris is au-
tomatically opened to full format and the slot diaphragm is opened to maximum aperture.

Full format, X-Iris open

•

Zoom must be disabled.

•

Release fluoro and wait until generator has performed automatic adjustment.

•

Switch fluoro off. The X-Iris is displayed on the monitor.

•

Use the keys for opening and closing the X-Iris to set the diameter of the superimposed
circle to the size of the X-iris.

•

In the "Available Functions:" window select "Open Pos - II. Full Format" and click on "Ex-
ecute".

•

Close the status window by clicking on the OK button.

X-ray radiation!
See Chapter 1, Safety Information.

Use radiation protection! Wear a lead apron!

WARNING

Содержание SIREMOBIL Iso-C

































































































































Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы:

Siemens SIREMOBIL Iso-C, Инструкция по эксплуатации, Страница: 50 / 128

Результаты поиска

Содержание SIREMOBIL Iso-C

Отзывы: