manualshive.com logo in svg

Siemens SIREMOBIL Compact L, Инструкция по эксплуатации, Страница: 65 / 86

Поделиться
Скачать
Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 65

Replacing boards / replacing components

6 - 13

Siemens AG

 

SPR2-130.061.02

Page 13 of 28

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

 

•

Rotate the camera in the in +220° position.

•

Mark the center again on the monitor (see Fig. 9).

•

Place an 8 mm washer over the three markings.
All three markings must be located within the 8 mm diameter of the washer. An 8 mm 
washer has a somewhat larger inner diameter of 8.4 mm, therefore the markings must 
clearly lie within the inner diameter and should not touch the edge of the washer.

•

If the diameter is <= 8 mm, the following centering adjustment does not have to be per-
formed. 
Continue with "checks and adjustments".

•

If the markings exceed > 8 mm, proceed as follows:

Centering the camera optics to the I.I. output

6

Prerequisite:

 The +220°, -220° and 0° positions were already marked as previously 

described.

•

Rotate the camera optics back to the 0° position.

•

Slightly loosen the three attachment screws of the camera optics.

•

Slightly loosen both excenter screws adjacent to the camera optics.

•

Move the camera optics toward the center, between both +220° and -220° markings (see 
also Fig. 9).

•

Switch fluoro on briefly and evaluate the position on the monitor. According to the ratio of 
the I.I. input screen diameter to the I.I. output screen diameter, a shift of the camera op-
tics by approximately 0.1 mm corresponds to a position shift of the washer displayed on 
the monitor of more than 1.3 mm (17 cm I.I.) or 1.7 mm (23 cm I.I.).

Fig. 9

X-ray radiation!
See Chapter 1, Safety Information.

Protect yourself against radiation exposure. Wear a lead apron.

WARNING

Содержание SIREMOBIL Compact L























































































Отзывы:

Нет отзывов