Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 86

Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 41

Adjustments / Programs

5 - 19

Siemens AG

SPR2-130.061.02

Page 19 of 30

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

Correction of the 0° position of the slot diaphragm display

5

•

Select the "Adjustments," "Parameter" menu at the service PC.

•

Select "Screen display Slot diaphragm" in the Combo box.

•

Click "Get from Unit".

•

Select "Rotation 0 degree position".

•

The parameter in the "Value Actual" field can be changed according to the minimum and
maximum values.

•

Then click "Set Value".

•

Click "Put to Unit".

•

After the SIREMOBIL Compact has booted, compare the 0° position of the slot dia-
phragm blades to the display on the monitor. If necessary, repeat the programming.

•

Click "Save to file" .

•

Leave the service program with "Logoff" and "Quit" to save the parameters as a new file
to disk.

Correct only if the slot diaphragms are shown at an angle of rota-
tion different from that displayed on the monitor. A correction of
+ 10° is possible. Camera rotation and slot diaphragm have to be
set correctly.

The service PC is connected to the serial interface of the
SIREMOBIL Compact.

The service program is started.

NOTE

«
...
39
40
41
42
43
...
»

Содержание SIREMOBIL Compact L























































































Отзывы:

Нет отзывов