Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 27

Страница: 27 / 86

Adjustments / Programs

5 - 5

Siemens AG

SPR2-130.061.02

Page 5 of 30

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

Dose rate adjustment

Prerequisites

•

The "Adjustment mode" parameter in the "Doserate adjustment" parameter group has
been programmed to "semi-automatic".

Preliminary steps

•

Switch on SIREMOBIL Compact.

•

Connect the service PC to the serial interface of the SIREMOBIL Compact.

•

Start the service program.

•

Select the "Diagnostics..." menu.

•

Select the "Monitoring..." menu.

•

Select the "Dose rate adjustment" menu from the Combo Box "Group 1".

•

Click on the button "UPDATE START".

•

The following is displayed on the service PC:

•

Insert 25 mm Al and 2.1 mm Cu at the radiation exit port of the SIREPHOS.

•

The grid remains on the I.I.

X-ray radiation!
See Chapter 1, Safety Information.

Protect yourself against radiation exposure. Wear a lead apron.

AUTO REGULATION

indicates the current status of the automatic adjustment.
(active / not active / manual / done)

BRIGHTNESS DEVIATION shows the difference in the actual brightness value minus the

nominal brightness value.

CONTROL CURVE

shows the currently selected fluoro curve (default: S2, antiiso-
watt 5 mA)

ADJUSTMENT

shows the operating control mode.
(Generator / Camera Iris / Stop)

I.I. ZOOM STATUS

shows the current I.I. format (survey / zoom)

DOSERATE

shows the dose rate selected.
(LOW / MID / HIGH)

TV-IRIS NOMINAL VALUE shows the stored or nominal TV-iris value from the learning

phase.
Note: An offset value is added to this value.
For this reason, the TV-IRIS NOMINAL VALUE and TV-IRIS
ACTUAL VALUE differ despite the correct adjustment
(BRIGHTNESS DEVIATION 0 + 3).

TV-IRIS ACTUAL VALUE

shows the actual TV iris value.

WARNING

Содержание SIREMOBIL Compact L























































































Результаты поиска

Содержание SIREMOBIL Compact L

Отзывы:

Siemens SIREMOBIL Compact L, Инструкция по эксплуатации, Страница: 27 / 86

Результаты поиска

Содержание SIREMOBIL Compact L

Отзывы: