Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 86

Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 25

Adjustments / Programs

5 - 3

Siemens AG

SPR2-130.061.02

Page 3 of 30

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

Checking the generator adjustment

5

•

With the system on, connect the service PC to the SIREMOBIL Compact.

•

Select "Test..." in the Diagnostic menu.

•

Select cassette simulation in "Function Groups".

•

Select cassette switch ON in "Available Functions".
The SIREMOBIL Compact is now in direct exposure mode.

•

Select 81 kV with the kV+ / kV- keys.

•

Select 8 mAs with the mAs+ / mAs- keys.

•

Connect oscilloscope channel 1 to D1.X46, ground at 0V.
Set the sensitivity to 1 V / Div.

•

Connect oscilloscope channel 2 to D1.X48, ground at 0 V.
Set the sensitivity to 2.5 V / Div.

•

Set the time to 25 ms / Div.

•

Set the oscilloscope to storage mode.

•

Release an exposure with the hand switch and store the oscillogram with the exposure.

•

Evaluate the stored oscillograms.
The tube current must reach the tolerance range of 13 mA + 1.5 mA in the time of 3 ms
and may not leave this range for the next 6 ms (the tube current may not run above
14.5 mA within the first 6 ms).
Refer also to oscillograms in Fig. 1 / Fig. 1a and Fig. 1b.

•

Select "Cassette switch off" on the service PC in "Available Functions".
Direct exposure mode is cancelled.

•

If the unit exceeds the tolerance range, the generator adjustment must be repeated.

X-ray radiation!
See Chapter 1, Safety Information.

Protect yourself against radiation exposure. Wear a lead apron.

WARNING

«
...
23
24
25
26
27
...
»

Содержание SIREMOBIL Compact L























































































Отзывы:

Нет отзывов