Siemens SIREMOBIL Compact L Скачать руководство пользователя страница 19

Страница: 19 / 86

3 - 1

Siemens AG

SPR2-130.061.02

Page 1 of 2

SIREMOBIL Compact

Medical Solutions

Rev. 11

09.04

CS PS 24

System Manual

Checking the operating voltages

Low voltages

Check the operating voltages for the SIREMOBIL Compact against the values in Table 1.

I.I. voltages

The voltages E1 / E2 / E3 and A may be taken from the I.I. test protocol and checked or
adjusted against the control test points listed in Table 2.

from test point

to test point

Voltage

Tolerance

Potentiometer

M14.4 (0V)

M14.5/6 (+5 V)

+ 5 V

+ 0.2 V

M14. +5 V/Adj.

M14.3 (0V)

M14.2 (+15 V)

+ 15 V

+ 0.1 V

M14. +15 V/Adj.

M14.3 (0V)

M14.1 (-15 V)

- 15 V

+ 0.5 V

M14. -15 V/Adj.

D3.X8.1 (0V)

D3.X8.3 (+26,75 V)

+26.75 V

+ 0.25 V

D3.R3

M13.S- (0V)

M13.S+ (+13 V)

+13 V

+ 0.2 V

M13.TR1

D3.X1.7 (0V)

D3.X1.9 (+24 V)

+ 26.5 V to

+ 29.5 V

n.a.

not adjustable

Tab. 1

Electrical voltage!
See Chapter 1, Safety Information.

Do not touch any part of the I.I. mini voltage supply!

Voltage

Test point

Ground

point

(0V)

Potentiome-

ter for full

format

Potentio-

meter

for zoom

format

Voltage

divider

ratio

UE1

P10

P11

1:1

UE2

1:1

UI 15

1:10000

30 kV, Anode

UI 30

1:10000

Tab. 2

WARNING

Содержание SIREMOBIL Compact L























































































Результаты поиска

Содержание SIREMOBIL Compact L

Отзывы:

Siemens SIREMOBIL Compact L, Инструкция по эксплуатации, Страница: 19 / 86

Результаты поиска

Содержание SIREMOBIL Compact L

Отзывы: