Siemens SiPass integrated Скачать руководство пользователя страница 62

Страница: 62 / 66

ASP Effect States

62 | 66

A6V11144326

ASP Effect States

The following table lists the Point Types and Properties that can be selected for

ASP Effect State.

Category Effect Type

Property

Property Values

Description

Input

Point

Regular

Effect

Input Enabled False

True

Enabled state of all the

input types except SPC.

Return to Time

Schedule

Control

True

Pulse command to

return to Time Control

Period.

Set Input

True

Command to set

Sintony input.

Clear Input

True

Command to clear

Sintony input.

Clear Isolate

Input

True

Command to clear

isolation of SPC Input.

Isolate Input

True

Command to isolate

Sintony/SPC input.

Stateless

Effect

Pulse Input

TrueTrue

Command to pulse

Sintony input.

Output

Point

Stateless

Effect

Toggle Output True

Toggles the door latch,

local, elevator state of

the output

Alternative

Effect

Dual State

Open
Closed

Output State of Door

Latch, Local, Elevator -

Open and Closed only

Regular

Effect

Unlock

Override

Interlock

True

Overrides the door

interlock state, setting

the state of the Latch

output to Unlock.

Stateless

Effect

Door Latch

Allow Access

Override Interlock

Overrides the door

interlock state setting

the state of the Latch

output to Allow Access

Single Pulse

Output

True

Unlock the output for a

single, short pulse

period for Door Latch

and Auxiliary.

Regular

Effect

Output Cancel

Perm

True

Cancel Permanent

Override Command.

Return to time

schedule

True

Return to Time Period

Control.

Stateless

Effect

Toggle

Auxiliary

True

Toggles the state of the

Auxiliary output.

Alternative

Effect

Aux Output

State

Open
Closed Pulse
Fast Pulse

Auxiliary Output state.

Содержание SiPass integrated



































































Результаты поиска

Содержание SiPass integrated

Отзывы:

Siemens SiPass integrated, Справочное руководство, Страница: 62 / 66

Результаты поиска

Содержание SiPass integrated

Отзывы: