Siemens SiPass integrated Скачать руководство пользователя страница 54

Страница: 54 / 66

ASP Trigger States

54 | 66

A6V11144326

ASP Trigger States

The following table lists the Point Types and Properties that can be selected for

ASP Trigger State.

Category Trigger Type

Property

Property Values

Description

Input

Point

Condition/Eve

Input Logical

State

Alarm
Normal
Tamper
Disabled
Enabled

Logical state of the

input.

Device Input

State

Short
Normal
Active
Open

Physical state of the

input.

Door Frame

State

Door Forced
Door Closed
Door Held
Door Tamper
Input Disabled
Door Opened

Logical state of

Doorframe input.

Input Enabled True

False

Enabled state of input.

Tamper

Logical State

Input Tamper
Input Fault
Tamer or Fault Cleared

Indicates Tamper or

Fault state.

Intrusion

State

Input Alarm
Input Normal
Input Tamper
Input Disables
Input Isolated

Input Logical state

related to intrusion

Zone inputs.

Physical

Enable State

Input Disabled (HW)
Input Enabled (HW)

Indicates if Input

Physically dis-abled

by FLN device.

Event Only

Passback

Triggered

True

COV only event for

Passback triggered.

Input

Unsealed

True

COV only event for

Input Unsealed.

Input Sealed True

COV only event for

Input Sealed.

Passback

Denied

True

COV only event for

Passback Denied.

Содержание SiPass integrated



































































Результаты поиска

Содержание SiPass integrated

Отзывы:

Siemens SiPass integrated, Справочное руководство, Страница: 54 / 66

Результаты поиска

Содержание SiPass integrated

Отзывы: