Siemens SiPass integrated Скачать руководство пользователя страница 48

Страница: 48 / 66

Controller Event Tasks
Sources

48 | 66

A6V11144326

Type

State (trigger)

Description

Exit Delay Timer

Started

An event task will be triggered when the exit

delay timer has started.

Normal

An event task will be triggered when the

intrusion area enters the normal state.

Part Armed

Intrusion Area has been Part Armed.

Part Armed B

Intrusion Area has been Part Armed B. (SPC

only)

Keypad

Standard Event

An event task is triggered when the “enter” or

“#” key has been pressed at an access point

with a keypad.

Output Point

Locked

Output point has been locked.

Unlocked

Output point has been unlocked.

Reader

Smart Card Event

An event task is triggered when an event task

is triggered when a MIFARE smart card has

been badged at an access point.

Standard Card Event An event task is triggered when a standard

access card (non-smart card) has been

badged at an access point.

Time Schedule

End

An event task is triggered when the selected

Time Schedule ends.

Start

An event task is triggered when the selected

Time Schedule begins.

Start and end

An event task is triggered when the selected

Time Schedule begins, and again when it

ends.

Содержание SiPass integrated



































































Результаты поиска

Содержание SiPass integrated

Отзывы:

Siemens SiPass integrated, Справочное руководство, Страница: 48 / 66

Результаты поиска

Содержание SiPass integrated

Отзывы: