Siemens SiPass integrated Скачать руководство пользователя страница 41

Страница: 41 / 66

Controller Event Tasks

Sources

A6V11144326

41 | 66

Controller Event Tasks

SiPass

integrated

allows you to define a controller event task that performs a

certain task (command) when a specific set of circumstances have been met

(trigger).
Because controller event tasks are triggered by hardware events, you must select

what type of component triggers or responds to the event.
The following table lists the Types and States that can be selected when defining a

Trigger for a Controller Event Task.

8.1

Sources

Type

State (trigger)

Description

ACC Event Task

Cleared

Allows the operator to trigger a Controller

Event Task as a result of another Controller

Event Task.
The ACC controller event task selected in the

Source field has not been triggered or has

been reset.

Set

The ACC controller event task selected in the

Source field has been triggered.

Access Point

(logical)

“Daily Code” mode

set

Access Point mode set to Daily Code.

“No Additional

Access” mode set

Access Point mode set to No Additional

Access.

“No Dual Custody”

mode set

Access Point mode set to No Dual Custody

mode.

“PIN as Card” mode

set

Access Point mode set to Daily Code.

“Standard Dual

Custody” mode set

Access Point mode set to Daily Code.

“Supervisory Dual

Custody” mode set

Access Point mode set to Daily Code.

Disable Intrusion

Control

Intrusion Control is disabled on the access

point.

Dual Custody

Verification

Complete

Dual Custody verification has been completed

at the access point.

Enable Intrusion

Control

Intrusion Control has been enabled at the

access point.

Invalid Daily Code

An event task is triggered when an invalid daily

code has been entered at an access point.

Reader Online

An event task is triggered when a reader

enters the offline state. Only valid for the

Siemens reader range.

Reader Offline

An event task is triggered when a reader

enters the online state. Only valid for the

Siemens reader range.

Reader Tamper

An event task is triggered when a reader

enters the tamper state (tamper input

activated). Only valid for the Siemens reader

range.

Содержание SiPass integrated



































































Результаты поиска

Содержание SiPass integrated

Отзывы:

Siemens SiPass integrated, Справочное руководство, Страница: 41 / 66

Результаты поиска

Содержание SiPass integrated

Отзывы: