manualshive.com logo in svg

Siemens SiPass integrated, Справочное руководство, Страница: 35 / 66

Поделиться
Скачать
Siemens SiPass integrated Скачать руководство пользователя страница 35

 

 

Host event tasks 

Targets / Commands 

7 

A6V11144326 

 

35 | 66 

 

7.2

 

Targets / Commands 

 

Target 

Command 

Description 

ACC Trigger 

Set Trigger 

An ACC Trigger allows you to trigger a Controller 

event task from a software event, like a Host 

event task. 
This Command activates the trigger selected. 

Any Controller Event tasks of type “Host Control” 

will be listed in the Location drop-down menu. 

Clear Trigger 

This Command clears the trigger selected, if it is 

currently activated. 

Access Point 

Allow Access 

Allow access as if a valid card has been 

presented at the reader. The door lock will re-

lock after the defined Latch time. 

Lock Door 

Locks the door temporarily until the next change 

in Time Schedule. 

Unlock Door 

Unlocks the door temporarily until the next 

change in Time Schedule. 

Set Mode “Card Only”

  Enables Card Only operation at an access point. 

Refer to Operational modes page 22 for more 

information. 

Set Mode “Card and 

PIN”

 

Enables Card and PIN operation at an access 

point. Refer to Operational modes page 22 for 

more information. 

Set Mode “H. V. Card 

Only”

 

Enables Host Verification Card Only operation at 

an access point. Refer to Operational modes 

page 22 for more information. 

Set Mode “H. V. Card 

and PIN”

 

Enables Host Verification Card and PIN 

operation at an access point. Refer to 

Operational modes page 22 for more 

information. 

Set Mode “V. O. Card 

Only”

 

Enables View Only Card Only operation at an 

access point. Refer to Operational modes page 

22 for more information. 

Set Mode “V. O. Card 

and PIN”

 

Enables View Only Card and PIN operation at an 

access point. Refer to Operational modes page 

22 for more information. 

Set Mode “D. R. Card 

Only”

 

Enables Delayed Reporting Card Only operation 

at an access point. Refer to Operational modes 

page 22 for more information. 

Set Mode “D. R. Card 

and PIN”

 

Enables Delayed Reporting Card and PIN 

operation at an access point. Refer to 

Operational modes page 22 for more 

information. 

Set Mode “Disabled”

  Disables an access point. Refer to Operational 

modes page 22 for more information. 

Restore Access Mode  Restores the previous access mode at an access 

point. Refer to Operational modes page 22 for 

more information. 

Reset Reader Tamper  Resets the reader tamper. Only applies to the 

Siemens reader range. 

Block Door 

Blocks the door and prevents cards from being 

used to gain access at the door using the 

selected reader. 

Содержание SiPass integrated



































































Отзывы:

Нет отзывов